Diaphragm valve
Diaphragm valves (or membrane valves) consists of a valve body with two or more ports, a flexible diaphragm, and a "weir or saddle" or seat upon which the diaphragm closes the valve. The valve body may be constructed from plastic, metal, wood or other materials depending on the intended use.
Categories
There are two main categories of diaphragm valves: one type seals over a "weir" (saddle) and the other (sometimes called a "full bore or straight-through" valve) seals over a seat. In general, straight-through diaphragm valves are used in on-off applications and weir-type diaphragm valves are used for control or throttling applications. While diaphragm valves usually come in two-port forms (2/2-way diaphragm valve), they can also come with three ports (3/2-way diaphragm valves also called T-valves) and more (so called block-valves). When more than three ports are included, they generally require more than one diaphragm seat; however, special dual actuators can handle more ports with one membrane.
Diaphragm valves can be manual or automated. Automated diaphragm valves may use pneumatic, hydraulic or electric actuators along with accessories such as solenoid valves, limit switches and positioners.
In addition to the well known, two way shut off or throttling diaphragm valve, other types include: Three way zero deadleg valve, sterile access port, block and bleed, valbow and tank bottom valve.
Valve body
Many diaphragm valve body dimensions follow the Manufacturers Standardization Society MSS SP-88[1] However, most non-diaphragm valves used in industrial applications are built to the ANSI/ASME B16.10 standard.[2] standard. The different standards makes it difficult to use diaphragm valves as an alternative to most other industrial valves. Some manufacturers offer diaphragm valves that conform to ANSI B16.10 standards thereby making these diaphragm valves interchangeable with most solid wedge, double disc, and resilient wedge gate valves as well as short pattern plug and ball valves.
Actuators
Diaphragm valves can be controlled by various types of actuators e.g. manual, pneumatic, hydraulic, electric etc. The most common diaphragm valves use pneumatic actuators; in this type of valve, air pressure is applied through a pilot valve into the actuator which in turn raises the diaphragm and opens the valve. This type of valve is one of the more common valves used in operations where valve speed is a necessity.
Hydraulic diaphragm valves also exist for higher pressure and lower speed operations. Many diaphragm valves are also controlled manually.
Body materials
- Brass
- Steel type:
- Cast Iron
- Ductile iron
- Carbon Steel
- Stainless Steel
- Alloy 20
- Plastic type:
- ABS (Acrylonitrile butadiene styrene)
- PVC-U (Polyvinyl chloride, unplasticized) also known as PVCu or uPVC
- PVC-C (Polyvinyl chloride, post chlorinated) also known as PVCc or cPVC
- PP (Polypropylene)
- PE (Polyethylene) also known as LDPE, MDPE and HDPE (see note)
- PVDF (Polyvinylidene fluoride)
- PTFE
- PFA
Body lining materials
Depending on temperature, pressure and chemical resistance, one of the following is used:
Diaphragm materials
- Unlined or Rubber Lined Type:
- NR/Natural Rubber
- NBR/Nitrile/Buna-N
- EPDM
- FKM/Viton
- BUNA-N
- SI/Silicone rubber
- Leather
- Fluorine Plastic Type:
- FEP, with EPDM backing
- PTFE, with EPDM backing
- PFA, with EPDM backing
Applications
Diaphragm Valves are ideally suited for:
- Corrosive applications, where the body and diaphragm materials can be chosen for chemical compatibility. (E.G. Acids, Bases etc.)
- Abrasive applications, where the body lining can be designed to withstand abrasion and the diaphragm can be easily replaced once worn out
- Solids entrained liquids, since the diaphragm can seal around any entrained solids and provide positive seal
- Slurries, since the diaphragm can seal around entrained solids and provide positive seal
Markets
Diaphragm valves have many applications in the following markets:
See also
References
External links
- History of the diaphragm valve, internet archive
- Internal Structure of the diaphragm valve, internet archive
- Pneumatic Actuators for diaphragm valves
- v
- t
- e
concepts
- Air gap (plumbing)
- Backflow
- Compatibility (chemical)
- Corrosion
- Drain (plumbing)
- Drinking water
- Fuel gas
- Friction loss
- Grade (slope)
- Greywater
- Heat trap
- Hydrostatic loop
- Leak
- Neutral axis
- Onsite sewage facility
- Pressure
- Sanitary sewer
- Sewer gas
- Sewage
- Sewerage
- Siphon
- Storm sewer
- Stormwater
- Surface tension
- Tap water
- Thermal expansion
- Thermal insulation
- Thermosiphon
- Trap (plumbing)
- Venturi effect
- Wastewater
- Water hammer
- Water supply network
- Water table
- Well
- Brazing
- British Standard Pipe (BSP)
- Cast iron pipe
- Chemical drain cleaners
- Compression fitting
- Copper tubing
- Crimp (joining)
- Drain-waste-vent system
- Ductile iron pipe
- Flare fitting
- Garden Hose Thread (GHT)
- Gasket
- Hydronics
- Leak detection
- National Pipe Thread (NPT)
- Nominal Pipe Size (NPS)
- O-ring
- Oakum
- Pipe (fluid conveyance)
- Pipe dope
- Pipe support
- Plastic pipework
- Push-to-pull compression fittings
- Putty
- Sealant
- Sewage pumping
- Soldering
- Solvent welding
- Swaging
- Thread seal tape
- Threaded pipe
- Tube bending
- Water heat recycling
- Atmospheric vacuum breaker
- Automatic bleeding valve
- Automatic faucet
- Backflow prevention device
- Ball valve
- Bleed screw
- Booster pump
- Butterfly valve
- Check valve
- Chemigation valve
- Chopper pump
- Circulator pump
- Cistern
- Closet flange
- Concentric reducer
- Condensate pump
- Coupling (piping)
- Diaphragm valve
- Dielectric union
- Double check valve
- Eccentric reducer
- Expansion tank
- Faucet aerator
- Float switch
- Float valve
- Floor drain
- Flow limiter
- Flushing trough
- Flushometer
- Gate valve
- Globe valve
- Grease trap
- Grinder pump
- Hose coupling
- Manifold
- Needle valve
- Nipple (plumbing)
- Pinch valve
- Piping and plumbing fitting
- Plug (sanitation)
- Pressure regulator
- Pressure vacuum breaker
- Pressure-balanced valve
- Pump
- Radiator (heating)
- Reduced pressure zone device
- Reducer
- Relief valve
- Riser clamp
- Rooftop water tower
- Safety valve
- Sewage pump
- Street elbow
- Submersible pump
- Tap (valve)
- Thermostatic mixing valve
- Trench drain
- Vacuum breaker
- Vacuum ejector
- Valve
- Water tank
- Zone valve
- Accessible bathtub
- Bathtub
- Bidet
- Dehumidifier
- Dishwasher
- Drinking fountain
- Electric water boiler
- Evaporative cooler
- Flush toilet
- Garbage disposal unit
- Hot water storage tank
- Humidifier
- Icemaker
- Instant hot water dispenser
- Laundry tub
- Shower
- Sink
- Storage water heater
- Sump pump
- Tankless water heater
- Urinal
- Washing machine
- Washlet
- Water dispenser
- Water filter
- Water heater
- Water softener
and control
trades,
and services
organizations
and standards
- Fire sprinkler system
- Piping
- Template:HVAC
- Template:Public health
- Template:Sewerage
- Template:Toilets
- Template:Wastewater