Rooftop water tower
A rooftop water tower is a variant of a water tower, consisting of a water container placed on the roof of a tall building.
This structure supplies water pressure to floors at higher elevation than public water towers.[1]
As building height increases, the vertical height of its plumbing also increases. This produces a large water column and the weight of this water produces very high pressure at the bottom of the column. Normally, this would require very thick (heavy-duty) plumbing to survive the pressure. Fittings at the bottom of the column would need pressure reducing valves to operate normally, and municipal water pressure would need to be very high to supply pressure to the top of the column.
Instead, the plumbing at various levels of the building are often sequestered, with pressure supplied from a rooftop water tower instead of the municipal supply. The tower itself is fed by a pump and a relatively high pressure line that carries water to the top of the building from the pipes below.
Beside this, also tall buildings with water tanks in the structure of the building exist. The tanks of such buildings usually do not serve only for keeping water pressure in higher floors, but often also for the public water supply.
Maintenance
Regular cleaning of tanks in use is necessary, in order to prevent possible water contamination.[2] Cleaning a water tank usually takes about six hours depending on the size of the tank. Most tanks in New York City are around 12 ft high and similar in diameter. This process includes scraping away the sediment and any debris that the tank has accumulated, then the interior surfaces are cleaned with a chlorine solution. Routine inspection for holes and cracks is also necessary, to prevent the intrusion of contaminants. Any holes are calked with epoxy and the metal hoops used to secure the walls of the tank are tightened to spec.[3]
In 2009, New York City passed new laws forcing property owners to have their tanks inspected annually, with proof of inspection. Inspection reports must also be available to all tenants in the building. If any unsatisfactory results are found, the individual responsible for the building must immediately have the tank cleaned up to city safety standards. Failure to comply with these rules can lead to the imposition of fines on the property owner.[2][4]
See also
- Water tower – Elevated structure supporting a tank
- Water tank – Container for storing water
References
- ^ Joseph, Sean (7 April 2009). "Water towers: NYC's misunderstood icons". amNewYork. Retrieved 6 August 2016.
- ^ a b Runyeon, Ray Rivera, Frank G.; Buettner, Russ (2014-01-27). "Inside City's Water Tanks, Layers of Neglect". The New York Times. ISSN 0362-4331. Retrieved 2017-01-17.
{{cite news}}
: CS1 maint: multiple names: authors list (link) - ^ "Proper Maintenance is Essential - Rooftop Water Tanks". cooperator.com. Retrieved 2019-11-21.
- ^ "water tanks | NYC Rules". rules.cityofnewyork.us. Retrieved 2019-11-21.
- v
- t
- e
concepts
- Air gap (plumbing)
- Backflow
- Compatibility (chemical)
- Corrosion
- Drain (plumbing)
- Drinking water
- Fuel gas
- Friction loss
- Grade (slope)
- Greywater
- Heat trap
- Hydrostatic loop
- Leak
- Neutral axis
- Onsite sewage facility
- Pressure
- Sanitary sewer
- Sewer gas
- Sewage
- Sewerage
- Siphon
- Storm sewer
- Stormwater
- Surface tension
- Tap water
- Thermal expansion
- Thermal insulation
- Thermosiphon
- Trap (plumbing)
- Venturi effect
- Wastewater
- Water hammer
- Water supply network
- Water table
- Well
- Brazing
- British Standard Pipe (BSP)
- Cast iron pipe
- Chemical drain cleaners
- Compression fitting
- Copper tubing
- Crimp (joining)
- Drain-waste-vent system
- Ductile iron pipe
- Flare fitting
- Garden Hose Thread (GHT)
- Gasket
- Hydronics
- Leak detection
- National Pipe Thread (NPT)
- Nominal Pipe Size (NPS)
- O-ring
- Oakum
- Pipe (fluid conveyance)
- Pipe dope
- Pipe support
- Plastic pipework
- Push-to-pull compression fittings
- Putty
- Sealant
- Sewage pumping
- Soldering
- Solvent welding
- Swaging
- Thread seal tape
- Threaded pipe
- Tube bending
- Water heat recycling
- Atmospheric vacuum breaker
- Automatic bleeding valve
- Automatic faucet
- Backflow prevention device
- Ball valve
- Bleed screw
- Booster pump
- Butterfly valve
- Check valve
- Chemigation valve
- Chopper pump
- Circulator pump
- Cistern
- Closet flange
- Concentric reducer
- Condensate pump
- Coupling (piping)
- Diaphragm valve
- Dielectric union
- Double check valve
- Eccentric reducer
- Expansion tank
- Faucet aerator
- Float switch
- Float valve
- Floor drain
- Flow limiter
- Flushing trough
- Flushometer
- Gate valve
- Globe valve
- Grease trap
- Grinder pump
- Hose coupling
- Manifold
- Needle valve
- Nipple (plumbing)
- Pinch valve
- Piping and plumbing fitting
- Plug (sanitation)
- Pressure regulator
- Pressure vacuum breaker
- Pressure-balanced valve
- Pump
- Radiator (heating)
- Reduced pressure zone device
- Reducer
- Relief valve
- Riser clamp
- Rooftop water tower
- Safety valve
- Sewage pump
- Street elbow
- Submersible pump
- Tap (valve)
- Thermostatic mixing valve
- Trench drain
- Vacuum breaker
- Vacuum ejector
- Valve
- Water tank
- Zone valve
- Accessible bathtub
- Bathtub
- Bidet
- Dehumidifier
- Dishwasher
- Drinking fountain
- Electric water boiler
- Evaporative cooler
- Flush toilet
- Garbage disposal unit
- Hot water storage tank
- Humidifier
- Icemaker
- Instant hot water dispenser
- Laundry tub
- Shower
- Sink
- Storage water heater
- Sump pump
- Tankless water heater
- Urinal
- Washing machine
- Washlet
- Water dispenser
- Water filter
- Water heater
- Water softener
and control
trades,
and services
organizations
and standards
- Fire sprinkler system
- Piping
- Template:HVAC
- Template:Public health
- Template:Sewerage
- Template:Toilets
- Template:Wastewater